Does anyone have a picture of the location of the TCM or EATC module (transmission) Mitchell says left front of engine compartment but I can't locate this one.
Build date 11/2000
2000 P/T Cruiser TCM Location
- wbuxton
- 1000 Club: Interstellar
- Posts: 1293
- Joined: Fri Jan 05, 2007 8:08 am
- Location: 30 miles west of Fort Worth
- Contact:
2000 P/T Cruiser TCM Location
Uncle PETA said I could come back.
William
Weatherford, TX
817-599-7680
866-744-3887
http://www.phoenixtrans.com
William
Weatherford, TX
817-599-7680
866-744-3887
http://www.phoenixtrans.com
- ricmorin
- 5K Holy Smokes Contributor
- Posts: 5976
- Joined: Mon Jul 25, 2005 10:11 am
- Location: New Hampshire
- Contact:
Re: 2000 P/T Cruiser TCM location
Check your email. Picture sent.wbuxton wrote:Does anyone have a picture of the location of the TCM or EATC module (transmission) Mitchell says left front of engine compartment but I can't locate this one.
Build date 11/2000
Ric Morin - Volunteer Forum Moderator, Shop Owner, ASE Master L1
Motorcar Alternatives, LLC
603-622-6434 x203
www.motorcaralternatives.com
I find my life is a lot easier when I use Special Orders
Motorcar Alternatives, LLC
603-622-6434 x203
www.motorcaralternatives.com
I find my life is a lot easier when I use Special Orders
- ricmorin
- 5K Holy Smokes Contributor
- Posts: 5976
- Joined: Mon Jul 25, 2005 10:11 am
- Location: New Hampshire
- Contact:
Re: 2000 P/T Cruiser TCM location
You take the LF wheel and wheel well off and it's bolted to the outside of the frame rail.
Ric Morin - Volunteer Forum Moderator, Shop Owner, ASE Master L1
Motorcar Alternatives, LLC
603-622-6434 x203
www.motorcaralternatives.com
I find my life is a lot easier when I use Special Orders
Motorcar Alternatives, LLC
603-622-6434 x203
www.motorcaralternatives.com
I find my life is a lot easier when I use Special Orders
- wbuxton
- 1000 Club: Interstellar
- Posts: 1293
- Joined: Fri Jan 05, 2007 8:08 am
- Location: 30 miles west of Fort Worth
- Contact:
Re: 2000 P/T Cruiser TCM Location
Much thanks, wheel well in my thinkig is outside the engine compartment. ![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
Uncle PETA said I could come back.
William
Weatherford, TX
817-599-7680
866-744-3887
http://www.phoenixtrans.com
William
Weatherford, TX
817-599-7680
866-744-3887
http://www.phoenixtrans.com
- ricmorin
- 5K Holy Smokes Contributor
- Posts: 5976
- Joined: Mon Jul 25, 2005 10:11 am
- Location: New Hampshire
- Contact:
Re: 2000 P/T Cruiser TCM Location
Well, it's close. And it IS LF.
Chrysler always puts these things in the most inhospitable places.![Crying or Very sad :cry:](./images/smilies/icon_cry.gif)
Chrysler always puts these things in the most inhospitable places.
![Crying or Very sad :cry:](./images/smilies/icon_cry.gif)
Ric Morin - Volunteer Forum Moderator, Shop Owner, ASE Master L1
Motorcar Alternatives, LLC
603-622-6434 x203
www.motorcaralternatives.com
I find my life is a lot easier when I use Special Orders
Motorcar Alternatives, LLC
603-622-6434 x203
www.motorcaralternatives.com
I find my life is a lot easier when I use Special Orders
- wbuxton
- 1000 Club: Interstellar
- Posts: 1293
- Joined: Fri Jan 05, 2007 8:08 am
- Location: 30 miles west of Fort Worth
- Contact:
Re: 2000 P/T Cruiser TCM Location
I found the picture in Mitchell finally. I was looking under "module location" figure 1-4 are listed. If you go to "transmission-automatic-locations" scroll down to fig 10 it is shown there with a picture.
Uncle PETA said I could come back.
William
Weatherford, TX
817-599-7680
866-744-3887
http://www.phoenixtrans.com
William
Weatherford, TX
817-599-7680
866-744-3887
http://www.phoenixtrans.com
- timbre4
- System Guru / Moderator
- Posts: 4476
- Joined: Tue May 25, 2004 5:47 pm
- Location: TN - Volunteer State
Re: 2000 P/T Cruiser TCM Location
Was going to report this then noticed that you submitted it by email to M1 like the true scout that you are. ![Idea :idea:](./images/smilies/icon_idea.gif)
![Idea :idea:](./images/smilies/icon_idea.gif)
Tim McDonnell -
Sr. Product Market Mgr / Forum Moderator / Mitchell 1 Media Developer
Sr. Product Market Mgr / Forum Moderator / Mitchell 1 Media Developer