Hello Everyone, hope all are well and busy I will try to be brief and to the point: 2015 Jeep Cherokee Latitude 3.2L V6 4wd First the Rear Differential was noisy and we replaced it with a "used'" One (10/19/21) then 5 months later the Transfer case came up with this code (C1477-4B - overheating clut...

Okay just to confirm what was happening with this car is, find out after the customer kept spraying something in the ignition that would build up on the key so the last time he came in, after a long time of searching TSB etc... Found that there was actually an issue with build up on the key, cleaned...

We have replaced the lock cylinder twice. It has now warmed up here and I'm suspecting that it is not happening to him
at the moment because of coarse I have not heard anything - is till a puzzler

That has to do with it not being a perfect world lol
thanks for the info

Yes that is the lock Cylinder. The worst part is it doesn't happen all the time. that's exactly what I thought is that moisture is some how getting in there but, it has been super cold here and not getting our freak rain, customer parts the car outside, so its not like it is in a heated garage. it i...

has anybody every heard of moisture getting in the ignition with, causing a layer of ice to build up on the key. Customer has to use a blow dryer on the ignition inorder to get the car started. the car is a 2010 Chevy Cobalt -- yes we are in Edmonton, Alberta Canada and it is cold but I have never h...

Happy New Year All, I wasn't quite sure where to post my question, but here it is. Why is there such a difference if some labor times in Mitchell verses All Data (sorry for swearing at you) We have Both programs, I always use the Mitchell but have others that always like to double check in All-Data ...

I spoke to John and he told me that in his testing he checked the wires in the connector for continuity and ground and both where good, unless there is a wire in the harness that is corroded and is still sending a good signal.
They also had the Coil wire right off to inspect it.

No John thought that as well before so he checked that and we both went out and just rechecked it and no it is not interfering, Heres another little thing we noticed when we were out there,
with the MAF Sensor unplugged and have running if barely touch the plug to the sensor it will quit

After Doing some more checking the MAF Sensor that is in the Car is the Hot wire Sensor. John ran voltage tests on all the wires going into the Sensor Etc... and everything tested normal, which should indicate a faulty Sensor, so after we got the new one and installed it would not run, could nit get...

When I called the Dealer to check on the part, I gave him the serial number, so I'm assuming from that he should have been able to give me the Correct number "I would hope" and when it came in it looked exactly the same as the one we took out, but I guess the question is the one we took out the corr...

It was a new Bosch Sensor from World Pac, with I initially called the Volvo Dealer and Got the part number and confirmed that it was a bosch MAF Sensor
and he said that they are the same other then packaging, if that is true or not I'm not sure.

Good Afternoon All !!! We have a 1993 Volvo 850 here, we scanned it and it had a MAF Code. Got in a new MAF Sensor and installed but car would not start, disconnect the MAF Sensor car starts, runs and idles; put old MAF Sensor back in Car will start and run but sets a MAF Code again, Repaired some l...

2009 Dodge Grand Caravan 3.3L came in cause had no power steering, was the Power Steering Return Line so we replaced it and fixed that problem, went to start the van and now we have NO RADIO its like there is now power there, Fuses all look good -- Not sure were to go next :( little confused as to w...

Just wondering if they are considering including the kilometers in with the miles in the Maintenance Schedules, it would make it a little easier and not so time consuming.

Gale

Excellent, Can't wait but I know thay can only work on a few changes at a time

Gale

I would be a nice feature to see in any of the next updates, to be able to Import a file to the workorder to save on file. Such as wheel alignment spec sheets, if we could import the Copy of the WA Results to the Mitchell invoice that corrisponds with it. It Would be Awesome and save time, cause eve...

Thank you, I know it did it before we changed, i never thought to look there

again thank you

Gale

There should be an option that if you have a business name listed and the customers name on the same page - it lists it in the WIP screen under the Customers name the not the Business Name. Personally I would like to see the Business name

Gale

Thank you again, I finally had time to go back and do some CSI work and Found it Doesn't cover them all but some - better then nothing
Prime Example the Nissan X-Trail - no info

Gale