not a stretch at all we all know if the battery gets below 9.6v modules will freek out there very well could be a internale short between the plates inside the battery. i was haveing an issue with a dodge diesel charging system the midtronics passed both batterys several times. untill a old timer ca...

no bus mess. on the cluster could very well be a cluster,bcm bus wires to or from any of the modules. pushed pin pwr or grd lose to a module. with a drb3 you can run a module scan when it acts up to try an isolate the problem. or with aftermarket scanners try and access the modules seperatly to see ...

not in indy local bmw labor rates start at $100.00 and go up depending on the work preformed

they also have issues with the dist. keep it for a couple of days do the fuel gauge taped to the wiper thing when it acts up youll know how to address it if youve got fuel presure, of course ck spark next. ive put a lot of fuel pumps as well as dist. in 2.5 liter cars. good luck and let us know how ...

thanks for the post well needed info

just a thought when i was going threw tech. training for chrysler they would allow the local independent shops to sit in on our training it was at no charge to the shops. the closest traing center for you would be in portland i dont know if its worth the call or not but the # for the center is 503-9...

in most states its against the law to sell a vehical with frame damage with out disclosing it. the issue will be were they aware of the damage. previous to the sell.

ill use dex 6 when ever its called for. were vin friendly around here what ever the manufacture recomends is what we use. i can tell you when atf+4 came out a lot of guys would use rear diff friction modifyer and the old style fluid to make up for the change in fluid properties to save money steven ...

unplug the mass air flow if it starts and stays running replace it,that or security issues on a start and die. ive had k/n air filters take out the maf due to excessive oil on the filter. good luck

put a radiator in it i have done a ton of them in b-vans there may be good flow but its only flowing threw the upper 1/2 of the radiator because the lower 1/2 is full of sediment. when you pull it ill bet it weights a ton. just a thought you can verify this with a temp gun start at the bottom and ru...

i have had a request in the past to convert a honda civic from pwr. too manual steering. the customer was of the opinion that the weight savings would make him go faster in the 1/4 mile?????????????? he had a ton of money in this little racer it was a simple operation he supplied the parts. but i am...

coffee out the noise,hay wheres that new keyboard i just bought

i agree with steven 100% the only way i would think of this repair is if the customer replaced the fuel pump,exhaust manafold as well as the cat. with a new factory o2 sensor and of course the repair would exceed the value of the vehical, kick it to the curb. inform the customer to drive it till it ...

you know i guess you could fill a library up with the stuff i havent seen. im from a snow state and had to googel auto snow chains i had no clue. i can remember in bad snow days helping my step dad which was a truck driver/owner operator. put on the old style chains not a good time. man would i have...

tim youtube.com punch in ford cab removal its a neat video of the proceedure filmed off the toolbox of a ford dealership tech. it should answer all your questions.

hay newbee reach in there and pull the hood latch on this jeep wrangler will ya

your not butting in this is a community effort all comments or questions are welcome. and welcome to the forum glad to have you

brian is right always go with the vin. but to answer your question 94-99 were listed as lh body which were the concord,intrepid,new yorker,vision and lhs all were lh bodys in 2000-04 they were listed as concord intrepid 300m they were also lh bodys 2000-04 were a concord body line with a lhs trim pa...

ive watched as inserts were put in a v-10 ford they were new to me they came from the cornwell tool guy ford oem tool is what he was trying to sell me. as his buddy installed them. he hasnt had a problem yet i just dont like the jb weild thats used. or the fact you use the spark plug as an insertion...